Control Panel
Switches: (8) Momentary Push Buttons Display: 4 Digit, 7-Segment,
0.56 Inch
Memory: Nonvolatile, retention >40 years
Microprocessor: 48MHz, ARM-7, 32-Bit MCU
USB Interface
Class/Rev: Low Speed, 1.5Mbps, USB-1.1 Connector: Type-B
RS-232 Interface
Baud Rate: 9600 default, 57600 max Configuration: DCE (use straight
thru cable) Connector: Sub-D 9 Pin Female
Digital Pulse Input
Input Impedance: 100k Ohm
Pulse Polarity: Pos or Neg
Threshold: TTL, LVTTL, 1.5V
Hysteresis: 0.75V Pulse
Width: 2us Min
Connector: BNC Jack
Analog Input
Input Impedance: 1M Ohm
Scale Factor: 10mV / Degree
Unipolar Range: 0/+3.600V, 0/360°
Bipolar Range: -1.800/+1.800V, -180°/+180°
Disable Range: > 4V
Pull-up Current: 5uA
Driving Source Z: 200 Ohm Max Recom Connector: BNC Jack
Analog Output
Output Impedance: < 1 Ohm
Scale Factor: 10mV / Degree
Unipolar Range: 0/+3.600V, 0/360°
Bipolar Range: -1.800/+1.800V, -180°/+180°
Output Current: 40mA Max
Short Duration: Unlimited
Connector: BNC Jack
Power Supply
Power/Type: 50W, Universal PFC SMPS
Line Voltage: World-Wide 85-265VAC
Line Frequency: 50/60Hz
Line Current: Sinusoidal, 8% THD
Switching Freq: 150kHz, Dithered
Standards: IEC 60950/61010, UL-1950 CISPR-22, FCC Class-B
Connector: IEC-320 Universal Inlet |
Main System
Operation: Mount any orientation, Ta 0° to 40°C
Platter: Cast & Machined Aluminum A713
Base: Cast & Machined Aluminum A713
Bearing: 5 Inch Sealed Ball Bearing ABEC-1
Hub: 4 Inch Diameter, 0.8 Inch Wall
Axial Load: 2,000 lbs (900 kg) Max, Bidirectional
Radial Load: 200 lbs (230 kg) Max
Drive System: Irreversible Worm
Drive Scale: Accurate Screen Printed 1 Degree
Chassis: 16ga Steel
Drive System
Motor: NEMA-23 Stepper Motor
Controller: Bipolar Microprocessor Microstepping
Direction: Either Counterclockwise or Clockwise
Shaft: 0.375 Inch Dia, Steel 1040
Worm: 0.75 Inch SAE 4340 Hardened Steel
Worm Gear: 5.75 Inch SAE 65 Phosphor Bronze
Bearing: Sealed Ball Bearings ABEC-3
Torque: Standard: 43 N•M, HiTorque: 75 N•M
Velocity 0.3-3.0 RPM, Programmable
Acceleration: Shaped, controlled by Microprocessor
Resolution: 0.003125 Degree
Step Size: 0.1 Degree Min
Accuracy: ±0.05 Degree Typ
Origin: User Resettable
Center Through Hole
Diameter: 1.5 Inches (38mm)
Platter Dimensions
Height: 0.75 Inches (19mm)
Diameter: 16.0 Inches (406mm)
Mounting Holes: (4) 1/4-20 on 3.0 Inch BCD (76.2mm) Mounting Holes:
(8) 1/4-20 on 9.0 Inch BCD (228.6mm) Mounting Holes: (8) 1/4-20 on
15.0 Inch BCD (381.0mm)
Chassis Dimensions
Height: 3.3 Inches (84mm)
Width: 18.0 Inches (457mm)
Length: 18.0 Inches (457mm)
Base Diameter: 13.0 Inches (330mm)
Mounting Holes: (8) 1/4-20 on 6.0 Inch BCD (152.4mm) Mounting Holes:
(4) 1/4-20 on 12.0 Inch BCD (304.8mm)
Overall Dimensions
Height: 4.1 Inches (104mm)
Width: 18.0 Inches (457mm)
Length: 18.0 Inches (457mm)
Weight: 40 lbs (18 kg) |
